so 60v on the gain? should i just not mess with the bass boost? where should i put my frequency? if there are posts to this already it would be much appreciated for the links..
03-15-2011 10:12 AM
Sicaudio
Re: Bass Boost & Clipping
03-15-2011 08:24 AM
greenesthaze
Re: Bass Boost & Clipping
hello. i have a soundstream DTR1.1700D i was wondering what i should set the settings to for a RE MT15 1 ohm coils? i am shooting to give it 2500w 1250rms could someone help me out? thanks much.
01-25-2011 01:18 PM
Mrop-
Re: Bass Boost & Clipping
NOT FOUND says the link
12-16-2010 11:39 PM
Jedslck
Re: Bass Boost & Clipping
I need to learn how to use an o scope
06-29-2010 08:37 AM
~ROB~313
Re: Bass Boost & Clipping
Quote:
Originally Posted by iversonbaby
yes...a bass knob is nothing but like having a long ass screwdriver to turn the boost up. it ovverrides the knob. so u turn ur bass knob all the way its the same as turning the amp up all the way.
yeah i took my boss knob out too
06-27-2010 08:31 PM
iversonbaby
Re: Bass Boost & Clipping
Quote:
Originally Posted by ~ROB~313
sooo does the remote bass knob cause clipping also??
yes...a bass knob is nothing but like having a long ass screwdriver to turn the boost up. it ovverrides the knob. so u turn ur bass knob all the way its the same as turning the amp up all the way.
06-20-2010 11:57 AM
~ROB~313
Re: Bass Boost & Clipping
sooo does the remote bass knob cause clipping also??
06-17-2010 05:19 PM
profundus-sanus
Re: Bass Boost & Clipping
Quote:
Originally Posted by johnecon2001
To sell amps.
nothing but the truth, considering most vehicles peak in that general area anyway..
06-17-2010 03:20 PM
jbaudiophile
Re: Bass Boost & Clipping
Quote:
Originally Posted by BlackMag
this post saved me, after readin this i went outside and discovered the a**holes that installed my system had both my P.A. 3000db amps with the Bass Boost turned to the maximum, i immediately turned them both off....much better
yeah thats what happend to me. ive had clipping twise and once i almost bought new subs and the second time almost bought new amp. lol. the jerk who tuned my amp said that he was "profesional"
06-16-2010 11:40 AM
jbaudiophile
Re: Bass Boost & Clipping
this video like saved me from buying another amp. i thoughtmy amp was done till i turned down the bass boost and the gain
05-27-2010 09:12 PM
jbaudiophile
Re: Bass Boost & Clipping
this saved me. lol. i though my subs were done! until i watched that vid. i just turned down the boost and its good again. thanks
05-24-2010 11:50 AM
NCMEMPHIS21
Re: Bass Boost & Clipping
I have a memphis pr500 at 1ohm and with the bass knob off it doesent hit at all running 2 m3 4ohm dvc 10's at 1ohm, turn up the knob then BOOM the amp comes alive, is that normal?
04-27-2010 10:59 AM
nx04gt
Re: Bass Boost & Clipping
is it really
04-24-2010 08:09 PM
johnecon2001
Re: Bass Boost & Clipping
To sell amps.
04-24-2010 03:23 PM
nx04gt
Re: Bass Boost & Clipping
why do they put bass boost on amps then ?
04-11-2010 08:50 AM
-0nes-
Re: Bass Boost & Clipping
very good info now i need to find some one with if those devices
03-28-2010 07:16 AM
mike844
Re: Bass Boost & Clipping
That was a great video.thx.i never fully understood clipping just knew not to turn up the gain and bass boost to high.
11-01-2009 09:13 AM
corrie32
Re: Bass Boost & Clipping
I found this ( The Clipping effect test - 05-20-2005, 12:31 PM
--------------------------------------------------------------------------------
Clipping Test Results
________________________________________
Well, Talnlanky and I have finished the test and compiled the results. Our goal with this whole experiment was to get rid of a few possible erroneous preconceptions, learn a little and share the results with all the other readers. We attempted to be as objective as possible with our testing to be sure and give everyone accurate information. We had access to a great supply of accurate test equipment and plenty of samples to work with. I cannot guarantee these results 100% and that they will be the same for everyone, but I believe they are an accurate portrayal of the effects of a clipped signal played into a dynamic loudspeaker.
The basis of this test was to see how the effects of a clipped signal would affect driver failure. Failure in this test was thermal breakdown of the driver's voice coil. Thermal breakdown in the test was when the driver's voice coil either shorted out or opened up due to materials melting down. We scaled a few test drivers with power until we found out how much it would take to have thermal failure within 1 minute.
The test consisted of 16 drivers, 8 small drivers to be tested at 1 KHz and 8 larger drivers to be tested at 170Hz. The two different frequencies were chosen to see if cone movement played a major role in cooling effectiveness.
Two different signals were used in the test, a pure sine wave that measured less than .1 THD at the amplifiers output and a pure square wave that measured at least 34% THD at the amplifiers output.
Two different kinds of power were used during the test, normalized power between the square and sine (differing voltage drive) and non-normalized power between the square and sine (same voltage drive). We did this for two reasons, one; the normalized voltage would represent an amplifier driven into hard clipping, and that is what most people are concerned about. Two; normalized power was used to indicate the difference a square or sine would have on the loudspeakers voice coil at the same power level (like clipping your deck for instance, but still having the output of your amplifier at a relatively low level).
We used two drivers for each set of measurements and gave both results plus an average to help give accurate results. We also matched the pairs used in the test by their voice coil Le measured on a Suncor meter. Of the 16 drivers used, only three gave what appeared to be erroneous results, not to shabby! Power measurements were made using a small signal through line power meter to ensure the square and sine waves were matched relatively well, and then the power increased linearly with the sine to be used as a reference. We were within 10% with our power matching, which is still pretty decent. It is very difficult to measure square wave power into a reactive load. You cannot use an average meter as you are dealing with peak currents in a full duty cycle signal with a crest factor of 1.
The results-
It was very surprising to see how much power these drivers actually handled! The 4" drivers were rated at 5wrms and the 5" drivers at 25wrms. Both drivers took much more than that to be driven to failure as the attachments will show.
Normalized voltage (AKA amp at full clipping). This shouldn't have been much of a surprise to anyone knowing that a square wave with the same Pk-Pk voltage as a sine will have almost double the power. As you can see on the spreadsheet and graphs, power handling severely dropped when the square wave was applied in this test. Time to failure was cut by a factor of 4 for most drivers.
Normalized power was a little more interesting. We could not prove within the scope of our test that a different signals of normalized power would have any different effects on the driver, regardless of the amount of cone excursion. Some people may still argue this, but it seemed pretty clear to us that weather a square or sine was put into a driver at a normalized power level, it still failed about evenly.
An extra test.... Remember when some people say "It doesn't even matter if it is only a few watts, if it's pure distortion, it will ruin your woofers".... Well we took a 10 watt square wave and ran it into a Pioneer 10" subwoofer for a few hours.... Nothing happened to it, of course, the motor didn't even get hot....
This test also only dealt with lower frequency drivers (in the big scheme of things) and is in no way meant to represent tweeters or any other driver that requires a filter network to provide a safe operating environment. That is a whole other ball of wax.
We hope that everyone gets something positive out of this and we had a great time doing the test!
I would like to thank the following people for all their help and knowledge, I know I forgot a few, but here we go anyway-
Talnlanky- Did the whole test, took the pictures and compiled all the data for you guys to see
Victor Tiscareno- Smartest dude I know
Sergey- Helped us realized how tough this would be!
Dan Wiggins- "its real easy Mike, if you have a resistive load....."
Hugh Dean- Designs awesome amps and gave some great pointers
Black00- Always gives us great ideas when destruction is involved
Parts Express- For having 49 cent drivers.....
-Mike Edgar
95Honda
View Public Profile
Send a private message to 95Honda
Find all posts by 95Honda
Add 95Honda to Your Buddy List
Page 2 of 2 < 1 2
05-09-2008 04:00 PM
kensaudio99
You will know when your subwoofer start to clip and distort. If you have good hearing and know what clipping and distortion sound like that your ear will know.
04-26-2008 03:56 PM
BlackMag
this post saved me, after readin this i went outside and discovered the a**holes that installed my system had both my P.A. 3000db amps with the Bass Boost turned to the maximum, i immediately turned them both off....much better
02-05-2008 01:23 PM
boltpride
I take it u didnt find it? lol. Thanks anyways bro..
01-31-2008 04:29 PM
Toyota Thundra
Lemme see if I can find it.
This thread has more than 25 replies.
Click here to review the whole thread.
buy & sell car audio stereo equipment. Purchase used amps, subs speakers for sale and buy classified listings for 12 volt amplifier and subwoofer sales forum
diymobileaudio.com is the DIY car audio install forum for automotive quality and spl stereo bass. 12 volt audio installation wholesalers buy amps, subs, double din car audio head unit electronics and ipod blue tooth car alarms at discounted prices